BUNDLE - R1250GSA Touring Front Engine Protector + Radiator Protectors
£199.65
£166.38 (ex. VAT)
R1250GSA Touring Front Engine Protector (Also fits Rallye) -Normally £65.60
This is our first product for the new 2018 R1250GS Rallye, it`s very similar to the previous type however it has been customised (by Mick) to include some beautiful detailing with the word `Rallye` which has been precisely laser profiled into the plate itself.
Made from high quality stainless steel and finished in a satin black powder coat. Its a front crud catcher designed to stop the bottom front of the engine getting `shot blasted` by grit and crud off the road - once water gets beneath the engine finish it can corrode terribly and look a right mess. Its also very expensive to sort out!
This Front Engine Protector locates on 4 of the existing fastening points and is held off the cover by 4 high quality hand finished stainless steel tubes. The Protector is held in place by 4 stainless steel fasteners with also come with the product.
It has been titled `touring` as it is larger than the smaller `sports` one and extends higher up the engine case giving better protection to the bottom of the engine case.
Top tip - what we did with ours was to apply ACF50 onto the engine casing before fitting the engine protector before fitting, ensuring the best guard against corrosion for the winter.
The engine protector also fits with the very popular Machineart Moto fender extender as shown in the images.
To fit only takes minutes and with a wipe with WD40 will look great for years to come.
It comes with full fitting instructions and you just have to contact us if you need any help over the phone fitting it.
BMW R1250GSA Radiator Protectors -Normally £120.00
With the introduction of the new R1250GSA model it became clear that a new design was called for.
This latest design is a joint design co-operation between Mark & Mike to produce these latest guards. Mark designed the framework geometry to ensure a very high quality fit into the OEM Radiator guard shroud (as you can see from the reverse image) whilst Mick applied his honeycomb design to the guard itself.
As you can see, Mick`s design offers larger holes than the OEM plastic guard – offering improved airflow over the original whilst adding extra strength by way of the stainless steel used in its construction.
Laser profiled to amazing accuracy (+/- 0.2mm), CNC formed and hand finished to remove all sharp edges. All of this is protected from the elements by the application of a satin black powder coat to ensure it outlasts any plastic or mild steel alternative.
To fit you simply remove the original plastic guard and replace with ours, which clicks perfectly into place – no drilling and it uses all the original fasteners.
Made in Britain, to order, by proud craftsmen who care – beware of cheap mass produced alternatives!
This is our first product for the new 2018 R1250GS Rallye, it`s very similar to the previous type however it has been customised (by Mick) to include some beautiful detailing with the word `Rallye` which has been precisely laser profiled into the plate itself.
Made from high quality stainless steel and finished in a satin black powder coat. Its a front crud catcher designed to stop the bottom front of the engine getting `shot blasted` by grit and crud off the road - once water gets beneath the engine finish it can corrode terribly and look a right mess. Its also very expensive to sort out!
This Front Engine Protector locates on 4 of the existing fastening points and is held off the cover by 4 high quality hand finished stainless steel tubes. The Protector is held in place by 4 stainless steel fasteners with also come with the product.
It has been titled `touring` as it is larger than the smaller `sports` one and extends higher up the engine case giving better protection to the bottom of the engine case.
Top tip - what we did with ours was to apply ACF50 onto the engine casing before fitting the engine protector before fitting, ensuring the best guard against corrosion for the winter.
The engine protector also fits with the very popular Machineart Moto fender extender as shown in the images.
To fit only takes minutes and with a wipe with WD40 will look great for years to come.
It comes with full fitting instructions and you just have to contact us if you need any help over the phone fitting it.
BMW R1250GSA Radiator Protectors -Normally £120.00
With the introduction of the new R1250GSA model it became clear that a new design was called for.
This latest design is a joint design co-operation between Mark & Mike to produce these latest guards. Mark designed the framework geometry to ensure a very high quality fit into the OEM Radiator guard shroud (as you can see from the reverse image) whilst Mick applied his honeycomb design to the guard itself.
As you can see, Mick`s design offers larger holes than the OEM plastic guard – offering improved airflow over the original whilst adding extra strength by way of the stainless steel used in its construction.
Laser profiled to amazing accuracy (+/- 0.2mm), CNC formed and hand finished to remove all sharp edges. All of this is protected from the elements by the application of a satin black powder coat to ensure it outlasts any plastic or mild steel alternative.
To fit you simply remove the original plastic guard and replace with ours, which clicks perfectly into place – no drilling and it uses all the original fasteners.
Made in Britain, to order, by proud craftsmen who care – beware of cheap mass produced alternatives!
MPN:
FALSE
Brand:
Cymarc
Weight:
0.6kg